dhcp6_messages.mes 4.64 KB
Newer Older
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
# Copyright (C) 2011  Internet Systems Consortium, Inc. ("ISC")
#
# Permission to use, copy, modify, and/or distribute this software for any
# purpose with or without fee is hereby granted, provided that the above
# copyright notice and this permission notice appear in all copies.
#
# THE SOFTWARE IS PROVIDED "AS IS" AND ISC DISCLAIMS ALL WARRANTIES WITH
# REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY
# AND FITNESS.  IN NO EVENT SHALL ISC BE LIABLE FOR ANY SPECIAL, DIRECT,
# INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
# LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
# OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
# PERFORMANCE OF THIS SOFTWARE.

$NAMESPACE isc::dhcp

% DHCP6_CCSESSION_STARTED control channel session started on socket %1
A debug message issued during startup after the IPv6 DHCP server has
successfully established a session with the BIND 10 control channel.

% DHCP6_CCSESSION_STARTING starting control channel session, specfile: %1
This debug message is issued just before the IPv6 DHCP server attempts
to establish a session with the BIND 10 control channel.

% DHCP6_COMMAND_RECEIVED received command %1, arguments: %2
A debug message listing the command (and possible arguments) received
from the BIND 10 control system by the IPv6 DHCP server.

% DHCP6_CONFIG_UPDATE updated configuration received: %1
A debug message indicating that the IPv6 DHCP server has received an
updated configuration from the BIND 10 configuration system.

% DHCP6_NOT_RUNNING IPv6 DHCP server is not running
A warning message is issued when an attempt is made to shut down the
IPv6 DHCP server but it is not running.

% DHCP6_NO_INTERFACES failed to detect any network interfaces
During startup the IPv6 DHCP server failed to detect any network
interfaces and is therefore shutting down.

% DHCP6_OPEN_SOCKET opening sockets on port %1
A debug message issued during startup, this indicates that the IPv6 DHCP
server is about to open sockets on the specified port.

% DHCP6_PACKET_PARSE_FAIL failed to parse incoming packet
The IPv6 DHCP server has received a packet that it is unable to interpret.

% DHCP6_PACKET_RECEIVED %1 (type %2) packet received
A debug message noting that the server has received the specified type
of packet.  Note that a packet marked as UNKNOWN may well be a valid
DHCP packet, just a type not expected by the server (e.g. it will report
a received OFFER packet as UNKNOWN).

% DHCP6_PACK_FAIL failed to assemble response correctly
This error is output if the server failed to assemble the data to be
returned to the client into a valid packet.  Additional messages will
detail the reason.

% DHCP6_QUERY_DATA received packet length %1, data length %2, data is <%3>
A debug message listing the data received from the client or relay.

% DHCP6_RESPONSE_DATA responding with packet type %1 data is <%2>
A debug message listing the data returned to the client.

% DHCP6_SERVER_FAILED server failed: %1
The IPv6 DHCP server has encountered a fatal error and is terminating.
The reason for the failure is included in the message.

% DHCP6_SESSION_FAIL failed to establish BIND 10 session (%1), running stand-alone
The server has failed to establish communication with the rest of BIND
10 and is running in stand-alone mode.  (This behavior will change once
the IPv6 DHCP server is properly integrated with the rest of BIND 10.)

% DHCP6_SHUTDOWN server shutdown
The IPv6 DHCP server has terminated normally.

% DHCP6_SHUTDOWN_REQUEST shutdown of server requested
This debug message indicates that a shutdown of the IPv6 server has
been requested via a call to the 'shutdown' method of the core Dhcpv6Srv
object.

% DHCP6_SRV_CONSTRUCT_ERROR error creating Dhcpv6Srv object, reason: %1
This error message indicates that during startup, the construction of a
core component within the IPv6 DHCP server (the Dhcpv6 server object)
has failed.  As a result, the server will exit.  The reason for the
failure is given within the message.

% DHCP6_STANDALONE skipping message queue, running standalone
This is a debug message indicating that the IPv6 server is running in
standalone mode, not connected to the message queue.  Standalone mode
is only useful during program development, and should not be used in a
production environment.

% DHCP6_STARTING server starting
This informational message indicates that the IPv6 DHCP server has
processed any command-line switches and is starting.

% DHCP6_START_INFO pid: %1, port: %2, verbose: %3, standalone: %4
This is a debug message issued during the IPv6 DHCP server startup.
It lists some information about the parameters with which the server
is running.